parts Archives

A part, or many parts, builds etc, this is a reference to parts of a build, or rebuild, parts 1 – 5 as an example for the M1 Refurb.

June 27, 2023September 27, 2024

Ender Filament and Adhesion Issues

Filament Challenges and More

Print Plate Surface Adhesion and Heating Issues

3D Printer Adhesion Issues with PLA and TPU

Lab Work – Ender Issues Defined

A few more weeks of Ender issues…

Ender Filament and Adhesion Issues, are causing a delay in the TPU Neo Max upgrade progress. I will be sharing more Ender ‘lite’ issues, as we continue the TPU trial and face filament challenges. The filament change was primarily for lab work on bait designs and future locking mechanisms where TPU will be more appropriate. Despite this tangent, core printing has not ceased, I am still facing challenges with PLA.

Ender Filament and Adhesion Issues

There are countless issues that seem infinite at the moment. Everything from Creality Software to Ultimaker Cura, Sonic Pad issues, filament running temp, and new surface temperature problems… we have a lot of cover. I will break these down into 2 or 3 new posts over the next week. We will also revisit surface adhesion. Surface adhesion and surface temperature seem to be causing most of the issues on the Ender Max Neo. I must admit, tinkering doesn’t always result in perfect prints, even 60% to 80% of the time. I won’t argue, I’ll just focus on testing… the more runs, the better chance we have of increasing that 60% likelihood of successful prints.

Pictures will follow, as they say, a picture is worth a thousand words. The pictures will be shared to specifically cover thickness, fragility and test prints. Let’s get to printing!

June 12, 2023September 27, 2024

Ender 3 Max Neo Filament

Printer Base Stabilization, Adhesion and Print Heights

Ender 3 Max Neo Filament Solutions

Lab Work – TPU Speed and Cycle Times

For this article on the Ender 3 Max Neo Filament, a typical print cycle might run between 2-5 hours, possibly more. While the standard range has been 2-5 hours, we are now looking at 12 – 16 hours. Recently, we have extended the top maximum run times to just under 12 hours for our test models. Surprisingly, both print tests resulted in the a mess.

For the record, a paper towel holder caused this issue twice. Upon initial observation, as the prints moved vertically (up the y-axis), the printing quality deteriorated. Somewhere between the 4″ and 5″ mark, both test prints went awry.

I’m starting to think there is shaking issue with the table or even a stabilization issue where the printer. is located. Both issues might be addressed by printing the base slices, holder ends, screws, rods, and washers in a single print. These items should be printed separately to attach the towel roll and the rod. The rod that is slung between the holders can be printed in a secondary or tertiary step, This is mitigation issue number one, or we could address the stabilization directly. The printers are currently positioned where they stand, so there is not much I can do to move them around.

Once I received the new filament, we will print the rod. If it works, great. If not, then step two will be more tedious. The issue is mostly a space problem in the office. The filament should arrive later today, and I will post a quick summary once I finish printing the rod slice, assuming it is successful.

Ironically, a similar issue was occurring when I ran TPU through the machine. So we can conclude the Ender 3 Max Neo Filament post with this. Although I don’t think they are related, adhesion was the issue with TPU. Which we will address in a future post once we determine the correct nozzle temps, print speed, and adhesion setup. I have heard/read about using adhesion spray or glue stick. Another day, we will tackle those 3d printer issues/phantom printing phenomenon.

June 9, 2023September 27, 2024

3d Printer Usage

3d Printer UsageUsage, New and Refurbed

Best 3d Printers On the market ’23

Lab Work – 3d Printers

See 3D Poll Below (closed), participate in the ‘who’s who of 3D Printer Usage Brands and Manufacturers’.

The poll has since closed on 3D Printer Usage. However, what we discovered is interesting. The question was ‘What 3D printers have you used, any success’? We are specifically looking for a TPU thermoplastic polyurethane (TPU) filament option. Tests with the NEO Max have been inconsistent, mostly unsuccessful, unless we swap out filaments. Interesting right?

We have generally, stuck with Creality for sometime, maybe four years or more. Today, we are looking for the best TPU lite printer. Do you have any suggestions regarding 3D print usage or brand? We have used Dremel for cutting and sanding, typical applications for a Dremel tool. As for Prusa, we have only used their products in theory, as some items we have purchased were made via a Prusa lab or outsourced printer. Anyhow, we are looking for feedback or comments. Please kindly leave your commentary below.

Please note, if you’re looking to swap out resin liners for the CL-89 model, it is advisable to purchase a number of them in advance, as they can be difficult to find when global stock is low.

Let us know what you’re thinking?

June 9, 2023September 27, 2024

New Halot Sky LCD

Creality Halot Sky Resin 8.9″ LCD Change Out

Lab Work – LCD Screen

I know, we started the last post with “Before you start your own 3D printing…”; this post does follow suit. It looks like a bad LCD screen, that needs to be replaced, as well as the film stretched over the resin vat or possibly just some resin damage, for that matter.

We replaced the monochrome LCD screen on the deck of the Halot Sky while we wait for a new FEP resin vat. Please note, if you’re planning to change resin liners (if you manage to find the correct ones for CL-89), it’s a good idea to buy several of them because they can be difficult to find when global stock is low.

Swapped LCD Screen

Swap details: Deconstruct by removing all screws, covers and metal panels. Be careful to disconnect the wires and ribbon cable for the touchscreen. Replace the screen ribbon in the quick connect being careful to reattach the ribbon and black wire for the touchscreen.

Two, clean up any resin residue, pour over, and spillage now. I believe this is where we made a mistake. The spillage got under the screen, as shown in the featured image for the article. Have a bottle of alcohol on hand to make the cleanup process as easy and effortless as possible. It took about 15-20 minutes in total, as I mentioned, due to the large amount of spillage. Finally, remove the ribbon tape surround and a few screws to gain access to the LCD screen.

Ideally, you’ll want to take your time, being careful to not to rip the LCD tape, or misplace a screw. If you do lose any items, you can always find new pieces in the Spare Parts. If not, try the eBay shop. We will provide a link to our wares but it’s taking some time due to logistical issues. We also sell out items on eBay from time to time, so check them out – we currently have some King books available.

For those who only need the FEP release film, or for our future reference – FEP Release Film – (search eBay for FEP Release film). A side note: FEP film can be hard to find, so eBay might be your best source. If i were a betting man, which I’m not, eBay or Amazon might be the only two sites where you can find spare parts and film. Cheers!

Before we move off the Halot updates, I’d like to share other Halot usage, new Creality series, break-fixes, and finally the idea of adding a resin printer to the 3d printer arsenal.

As usual leave a comment below, let us know what you’re thinking?

May 2, 2023September 26, 2024

Need A Charge?

In A Pinch – Grab a 9v, a Car charger, electrical tape and a nail

Lab Work – 9v Charger Hack

Before you start criticizing me me about wattages, amperage, safety, or reality etc., I want to clarify that I meant to post this back in December, but didn’t get around to it until now. The scenario is familiar – no power due to a storm outage or a dead car battery, and you find yourself in a bind .You phone is dead, and you need a charge. This hack can be a lifesaver when you’re away from home comforts whether you’re camping, off-grid, or stranded due to breakdown.

I usually avoid cellphone hacks, but this one caught my attention as we enter hurricane season. Having experienced storms, tornadoes, hurricanes, and the like, I know that sometimes the simplest things can make a big difference in a power outage. I’m not suggesting you hoard batteries, clicky-pens, nails, and used charger cords, but it might be wise to have a few on hand, just in case.

This hack has been around for sometime. Some people believe that off-grid living and underground living may require alternative power sources, and this hack could be just what you need. In any case, we spliced together a few generic charging cords, added a car charger, and a few 9v batteries, and voila! We have some juice for the cellphone battery. This hack might work even better. This hack might work even better if you can find a different type of battery, such as an RC/Drone battery considering 9v, LiCB or 4s/5s LiPos. Whatever the case, you may have these items lying around your home, office, or shop, depending on your situation. We have these items in our workshop, so you can imagine how handy they might be in serious storm or power outage situation.

Like the quick fix format? Check out other quick fix content here such as this disposal problems fix. Like the learn to descale your coffee equipment – pots and machines, fix a toilet float clean and fix a pool filter housing and filter which is like this cell phone charging hack… Check them out!

As usual leave a comment below, let us know what you’re thinking?

April 14, 2023September 27, 2024

Halot Sky Break-fix

Halot Troubleshooting Break-fix

Creality Halot Sky – Resin Liner Change Out

Lab Work – Working Out The Bugs, Halot Sky Resin Printer

Before you begin you own 3D printing, journey, including purchasing a 3D printer, we need to discuss break-fix: the Halot Sky Break-fix which follows up on the LCD replacement just a few months ago. It is crucial to understand how to maintain and troubleshoot printers. The same applies to addressing major printing issues, such as breaking down the entire printer to the board level. This also includes dealing with misprints, which can occur frequently. Proper care, cleaning, and resin management are essential tasks, including swapping resin liners and cleaning resin drips meticulously.

Liner Change

Liner Frame

New Liner

Attached are few sneak peek video clips and photos of our latest test prints and demos. We have some ‘real-world’ solutions coming soon. More creations on 3D software and 3D applications such as TinkerCad, Autodesk – AutoCad, Creality (design) software, SolidWorks and more. We have started with TinkerCad and AutoCad so that we can print prototypes and finish products within a few hours. Got any ideas? Need 3d prints? Leave us a comment or drop us a line on the Connect. Please include: file type, filament, sizes etc. Let’s see what we can come up with! As usual leave a comment below, let us know what you’re thinking?

February 14, 2023September 27, 2024

New Creality Series

Creality Makers-space

Creality 3d Printing Series – Ender 3 Neo Max & Halot Sky

Lab Work – Creality Settings

3D printing? If you have a need, give us a call. We will be posting a handful of new work in the weeks to come. From testing and prototyping, to 3D model printing and extruding, resin printers versus PLA/TPU filament printers, the the trials and the tribulations i.e. issues we faced while running our 3D printers. Check out the latest Creality Ender series printers, as we will be covering the Max Neo in this article.

I have attached a few sneak peek video clips and photos of the New Creality Series, showcasing our latest test prints and demos. Als have some ‘real-world’ solutions coming out soon. We will also be putting out some polls regarding 3D software/applications – TinkerCad, AutoCad, Creality (design) software, SolidWorks and more. We have started with TinkerCad and AutoCad so that we can print prototypes to finish products within a few hours.

In The Lab

Creality Tablet

Prototypes

In The Lab

Got any ideas? Do you need 3D prints? Leave us a comment, drop us a line on the Connect, please include: file type, filament, sizes, etc. Let’s see what we can come up with!

As usual leave a comment below, let us know what you’re thinking?

December 15, 2022September 26, 2024

Ender, Halot & Prusa 3d

3d Printers, Resin Printers – Ender, Halot & Prusa 3d

Creality, Prusa or Something else? Ultimaker

Gear – 3d Printers

With the holiday season in full swing, thought it might be worth while to do some research on a 3D printer… Should we go with Ender, Halot & Prusa 3D? Should we choose extruded filament or resin? Which brand offers the best cost/benefit ratio?

After conducting our research, in shop testing, we found a printer that meets the shop needs. Once the device has been received, we will porovide more information. Stay tuned for updates on the device, our 3D lab startup, and our first runs. Let me know in the comments below: should I choose Prusa or Creality CR Series Ender series or Halot Series?

3D Printers

There are a couple of different models, filament types, series, etc. to choose from. We are considering the Ender 5 Plus, Halot Series (Resin) versus the Prusa I3 MK3S+. Perhaps some other tools to go with the printer as well, such as wash/cure, filament, bed, boxes/enclosures, etc. There are lots of options to consider. The point is, we are looking for the best option for the shop. Help us understand why and what factors might have influenced your decision to purchase a 3D printer. Should we choose something else? Dremel, MakerBot, Ultimaker, LulzBot… there are more options out there, but it is time to narrow down the list.

As usual leave a comment below, let us know what you’re thinking?

November 26, 2022September 27, 2024

AirMap by DroneUp

Take Flight, AirMap by DroneUp

AirMap for Drones, Setup and Flight App

Tech | Tools – Fly With Confidence – Airmaps

Get FAA approval to fly with AirMap by DroneUp… Are you looking for FAA compliant drone flight apps? Airmap makes flying easy and understandable. Fly with confidence while staying within legal requirements and having the knowledge to fly approved.

From installation to usage, AirMap by DroneUp for iOS or Airmap – for Android will help you understand what is happening in the airspace above you, how to fly with approved FAA flight status, log your flights, and more.

Airmaps iOS And Android

TFR

Welcome

Connect

FAA Plan

Zones

Restrictions

Brevard County

From t’s & c’s, to maps, flight logs and FAA approval to fly safely, make sure th get approved with FAA-approved flight requests. Check Kennedy Space Center to learn about the airspace above and around Kennedy. Familiarize yourself with the warnings and requirements, as well as the maps and flight restriction in and around the areas within your airspace.

Need more flight apps, or drone apps for flight approval? Leave us a comment below and we will find some additional drone apps for you. While you’re here take a look at other FAA related articles, FAA Hurricane Update from 10/1 and FAA Drone Safety from 4/19. Although these articles are now archived, it’s important to remember that drone flight rules are drone rules. Most importantly, make sure to stay compliant and safe while flying.

October 1, 2022September 27, 2024

FAA Hurricane Update

Hurricane Ian Alerts Update

Materials – FAA Hurricane Update

Know What To Do Pre/Post Hurricane Ian – Before you fly, understand the current conditions in the sky above you… FAA Hurricane Update. Remember, the drone industry is constantly evolving, growing and maturing.

Drone enthusiasts will always want to fly, so be sure to prioritize safety. This year, the FAA has organized a safety awareness day for drone pilots, federal representatives, educators, drone hobbyists and more… On June 18, 2022, join your fellow drone pilots for FAA Drone Safety Day. To participate – look for ‘about drone day’, support, or host an event. This message is in reference to FAA notice number” NOTC2405. For those seeking more information or a drone piloting app, consider trying Airmaps.

For those of you who are interested in learning more about open FAA communications, licensed drone updates etc. feel free to reach out to us or leave a comment below.