3d printer filament, filaments do vary – plastics, wood, carbon fiber, metal materials and more.  Key, the right filaments for your prints.

Ender 3 Max Neo Filament

Printer Base Stabilization, Adhesion and Print Heights

Ender 3 Max Neo Filament Solutions

Filament Everywhere

Lab Work – TPU Speed and Cycle Times

For this article on the Ender 3 Max Neo Filament, a typical print cycle might run between 2-5 hours, possibly more. While the standard range has been 2-5 hours, we are now looking at 12 – 16 hours. Recently, we have extended the top maximum run times to just under 12 hours for our test models. Surprisingly, both print tests resulted in the a mess.

For the record, a paper towel holder caused this issue twice. Upon initial observation, as the prints moved vertically (up the y-axis), the printing quality deteriorated. Somewhere between the 4″ and 5″ mark, both test prints went awry. 

I’m starting to think there is shaking issue with the table or even a stabilization issue where the printer. is located. Both issues might be addressed by printing the base slices, holder ends, screws, rods, and washers in a single print. These items should be printed separately to attach the towel roll and the rod. The rod that is slung between the holders can be printed in a secondary or tertiary step, This is mitigation issue number one, or we could address the stabilization directly. The printers are currently positioned where they stand, so there is not much I can do to move them around.

Once I received the new filament, we will print the rod. If it works, great. If not, then step two will be more tedious. The issue is mostly a space problem in the office. The filament should arrive later today, and I will post a quick summary once I finish printing the rod slice, assuming it is successful.

Ironically, a similar issue was occurring when I ran TPU through the machine. So we can conclude the Ender 3 Max Neo Filament post with this. Although I don’t think they are related, adhesion was the issue with TPU. Which we will address in a future post once we determine the correct nozzle temps, print speed, and adhesion setup. I have heard/read about using adhesion spray or glue stick. Another day, we will tackle those 3d printer issues/phantom printing phenomenon.

Ender, Halot & Prusa 3d

3d Printers, Resin Printers – Ender, Halot & Prusa 3d

Creality, Prusa or Something else? Ultimaker

Halot Sky Resin Printers

Gear – 3d Printers

With the holiday season in full swing, thought it might be worth while to do some research on a 3D printer… Should we go with Ender, Halot & Prusa 3D? Should we choose extruded filament or resin? Which brand offers the best cost/benefit ratio?

After conducting our research, in shop testing, we found a printer that meets the shop needs. Once the device has been received, we will porovide more information. Stay tuned for updates on the device, our 3D lab startup, and our first runs. Let me know in the comments below: should I choose Prusa or Creality CR Series Ender series or Halot Series?

3D Printers
blank

 

blank

 

There are a couple of different models, filament types, series, etc. to choose from. We are considering the Ender 5 Plus, Halot Series (Resin) versus the Prusa I3 MK3S+. Perhaps some other tools to go with the printer as well, such as wash/cure, filament, bed, boxes/enclosures, etc. There are lots of options to consider. The point is, we are looking for the best option for the shop. Help us understand why and what factors might have influenced your decision to purchase a 3D printer. Should we choose something else? Dremel, MakerBot, Ultimaker, LulzBot… there are more options out there, but it is time to narrow down the list.

As usual leave a comment below, let us know what you’re thinking?